Boiler Stove Central Heating Systems in Ireland
A boiler stove central heating system matters because it lets you heat your living space, radiators, and hot water from a single solid-fuel appliance, which can change both comfort and running costs in an Irish home.
You choose a stove that matches your heat demand, balancing room heat versus boiler output so you do not overheat the stove room while still feeding the radiators and cylinder. You also weigh fuel options and day-to-day usability, alongside efficiency, emissions expectations, and how features like air-wash affect real-world performance. Installation needs careful planning around flue design, ventilation, and safety components such as heat leak protection, while meeting Ireland’s Building Regulations requirements, including Part J for heat-producing appliances and Part L for energy performance.
If you already have an oil or gas boiler, the setup can often be integrated, but it depends on whether your system is open-vented or sealed and on getting the right controls and valves to keep heat sources from fighting each other. Ongoing maintenance, fuel consumption, and chimney sweeping also shape the total cost and the environmental impact, including how your choice aligns with Irish standards and any relevant SEAI guidance.
With those considerations in mind, it helps to get clear on what a boiler stove is and how it actually circulates heat through your central heating.
Boiler stoves are a popular Irish option when you want real flame heat in the living space but also want to push heat into radiators and, in many homes, the hot water cylinder as well. You get comfort where the stove sits, plus a meaningful contribution to space heating and hot water, but only when the stove output, plumbing layout, and safety controls are designed as one system. Pay attention to the split between heat to room and heat to water, confirm whether the model suits an open-vented or sealed setup, and plan for heat-dump protection and correct ventilation so the install stays safe and predictable in everyday use.
What is a Boiler Stove and How Does it Work?
A boiler stove is a solid-fuel stove with a built-in water jacket that captures heat and sends it into your central heating system. It’s used to warm the room it sits in while also heating radiators and, in many cases, your domestic hot water cylinder. The key nuance is that outputs are split between room heat and water heat, so sizing and plumbing design matter more than with a standard room-only stove, especially in typical Irish homes with mixed radiator and cylinder demand.
How it heats radiators and domestic hot water
This matters because once the stove is linked into pipework, it behaves like a heat source for your rads and cylinder, and SEAI’s DEAP documentation covers common Irish arrangements where a boiler appliance provides space heating and hot water through the primary circuit. Use the SEAI source as a general reference point for how systems are treated in Irish energy assessments: SEAI DEAP Guidance Document. With that basic system picture in mind, the real-world decisions come down to outputs, controls, and how safely the heat can be managed when the stove is running hard.
The practical Irish considerations
This matters for comfort and safety because a boiler stove needs the right controls, heat-dump protection, and a competent installer. Many boiler stoves are designed around open-vented plumbing arrangements, and your installer must confirm compatibility with your existing system and the manufacturer instructions for safety devices and controls. When you’re comparing outputs and formats, it helps to start by browsing real models sold for Irish homes and noting the stated room-to-water split on each listing: boiler stoves in Ireland. Once you have a shortlist, matching the stove to your radiator load and hot-water demand becomes much clearer.
Frequently Asked Questions About Boiler Stoves in Ireland
Can a boiler stove heat radiators and water?
Yes. A properly specified boiler stove can heat radiators and contribute to your domestic hot water, depending on how it’s plumbed and controlled. The key is checking each model’s stated output split, usually shown as heat to room (kW) and heat to water or boiler output (kW), so what you buy actually matches your radiator demand and cylinder needs rather than overheating the room the stove sits in.
Open or sealed system?
It depends on the model and on your existing heating setup. Many boiler stoves are installed on open-vented systems, and some installations can integrate with sealed systems using the correct safety kit and manufacturer-approved methods. This is not a DIY decision. Your installer should confirm the stove’s approved system type, required safety devices (such as heat leak or heat dump arrangements), and how it will interact with any existing boiler, pump, and controls so the system can safely dispose of heat during a power cut or when demand is low.
Do you supply flue kits and parts?
Yes. Alongside boiler stoves, you can source matching flue components and installation accessories through StoveBoss so you can plan the full route and spec rather than buying the appliance in isolation. This matters because correct flue sizing, safe clearances, and the right parts for your chimney or twin-wall flue setup are often what make the difference between a smooth install and a costly delay on fitting day.
Find a Boiler Stove That Matches Your Radiators and Hot Water Demand
Browse StoveBoss’s range of boiler models and shortlist options by heat output and room-to-water split so you can have an informed conversation with your installer before you buy. Start with the collection here: Boiler Stoves Ireland, and focus on the kW figures, the stated system suitability, and the flue requirements to make sure the stove you choose will work safely and comfortably in your home.
Size a boiler stove properly so it can heat your radiators and still keep the stove room comfortable, without having to run it flat-out every evening. Add up your radiator heat demand and match it to the stove’s water output (to radiators and hot water), while keeping an eye on room output (heat to the space the stove sits in) so the living area does not turn into a sauna. Let your home’s insulation level and layout influence the final kW choice, because a draughty older Irish house and a modern BER-friendly home behave very differently in winter. Use SEAI’s DEAP approach as a reality check on how solid-fuel systems are assessed for Irish dwellings, and always confirm the exact model’s fuel approvals and required safety controls with a qualified installer before you buy, as pipework layout, heat-leak protection and plumbing design can change what “enough output” really means. When you do that groundwork, you can shortlist confidently and move straight to comparing boiler stove models that genuinely suit your home.
Choosing the Right Boiler Stove for Your Irish Home
How do you size a boiler stove central heating system for an Irish home?
Start by totalling the radiators and estimating the heat demand room by room, then pick a boiler stove with enough water output for the system and enough room output for the living space. Adjust your choice for insulation level and how open-plan the stove room is. Confirm suitability for larger homes and fuels with your installer before you commit, because pipework layout and safety controls can change the required output, and those details often decide whether the system feels comfortable day to day.
1. Count radiators and match water output
This step matters because most boiler stove disappointment comes from not having enough heat going into the radiators. As a rule of thumb, more radiators and bigger rooms push you towards higher water-output models, while a small 6 to 8 radiator setup in a well-insulated house can often be served by a mid-range boiler stove. Once you have a realistic radiator total, the real question becomes how quickly your home loses that heat in Irish weather.
2. Factor in insulation and Irish BER realities
This step matters because insulation and airtightness decide how quickly your heat leaks away on a damp Irish winter evening. SEAI’s BER method notes how solid-fuel boiler systems are treated in the DEAP guidance document (2025) for Irish dwellings, which is why your home’s fabric standard should steer the kW you choose. When the heat-loss side is understood, it becomes easier to judge whether one appliance can comfortably carry a larger home and the fuels you want to burn.
3. Sanity-check larger homes and multi-fuel needs
This step matters because bigger, colder homes can need either a higher-output boiler stove or a second heat source to avoid running the stove flat-out. If fuel flexibility matters, shortlist from boiler stoves in Ireland and confirm the exact multi-fuel approvals (wood and smokeless fuel) on the stove’s data plate and manual before install. That same confirmation step is also the best moment to clarify the common sizing and suitability questions people have before they place an order.
Frequently Asked Questions About Boiler Stove Sizing in Ireland
What is the difference between water output and room output on a boiler stove?
A boiler stove’s water output is the portion of heat sent into the central heating circuit for radiators and, in some setups, domestic hot water. Room output is the heat emitted into the room where the stove is installed. You need enough water output to meet your radiator demand, but you also need a room output that suits the space, otherwise the stove room can overheat while the rest of the house still feels cool.
Can a boiler stove heat the whole house in an Irish property?
It can, but it depends on the home’s heat loss, radiator sizing, and system design. A well-insulated home with a sensible number of radiators is far easier to heat than a larger, older, draughty house with high demand. Many Irish homes also benefit from a supplementary heat source or careful zoning so you are not relying on one stove running hard for long periods in cold spells, which is a decision best made with your installer based on the actual layout and pipe runs.
Do I need a qualified installer for a boiler stove central heating setup?
Yes. A boiler stove connected to radiators is a plumbing and heating job that needs correct safety controls, correct pipework sizing, and safe integration with any existing system. The stove manufacturer’s instructions must be followed, and your installer should confirm the required safety devices for your exact setup, including how the system is protected if power fails or circulation is interrupted.
How does BER and SEAI guidance affect my boiler stove choice?
BER is influenced by the overall fabric of the home and how the heating system is assessed under the DEAP methodology. SEAI’s DEAP Guidance Document explains how systems are treated for Irish dwellings, so your insulation levels, airtightness, and controls matter as much as the stove’s quoted kW figures. In practical terms, better insulation usually means you can meet comfort needs with lower output, while poor insulation forces higher output and longer burn times.
Are all “multi-fuel” boiler stoves approved for wood and smokeless fuel in Ireland?
Not always. “Multi-fuel” is sometimes used broadly, so you should confirm exactly what fuels are approved for that model by checking the stove’s data plate and the manufacturer manual. This is especially important if you plan to burn smokeless fuels, as grate design, air controls, and manufacturer approvals vary by model, and the wrong assumption can lead to poor performance or warranty issues.
Find a Boiler Stove That Matches Your Radiators and Your Room
Browse StoveBoss’s boiler stoves in Ireland and shortlist models by water output and room output so your radiators get the heat they need without overheating the living space. If you already know your radiator total and insulation level, you can narrow your options quickly and bring a clear shortlist to your installer for a final suitability check before you buy.
Installation and Safety Considerations
Install a boiler stove central heating system by confirming the flue route and chimney condition, planning the plumbing tie-in and the required safety controls, and commissioning the stove exactly to the manufacturer’s instructions. Decide early whether you need an external air kit, because many modern Irish homes are more airtight and a stove can struggle for combustion air, which affects draw and controllability. Wrap up by having your installer document compliance and test alarms, because small shortcuts here can create very real fire and carbon monoxide risk, especially when the stove is tied into a wet heating circuit.
1. Confirm the flue connection and chimney integrity
This step matters because poor draught or leaks can smoke up the room and can spill carbon monoxide back into the living space. If you are still choosing an appliance, compare boiler outputs and flue options across boiler stoves before you lock in liner size and route, as the stove model you choose often dictates the flue diameter and connection details that must be followed on site. A clean, correctly sized, properly installed flue is what allows all the other safety measures to work as intended, so it is worth getting the basics right before any plumbing decisions are finalised.
2. Provide combustion air and plan EcoDesign suitability
This step matters because modern houses often need a dedicated external air supply to keep the stove stable and efficient, particularly where doors and windows have been upgraded and natural ventilation has been reduced. EcoDesign-ready models are worth prioritising because they are designed to cut smoke and improve controllability in real Irish winter use, which usually means better combustion performance when you are lighting, refuelling, and trying to keep steady heat during damp, changeable weather. Once you have reliable combustion air and a stove designed for cleaner burning, you can focus on the wet-side protections that prevent overheating and keep the whole system safe under load.
3. Fit wet-system safety and meet Part J/Part L expectations
This step matters because water overheating is the big risk on boiler stoves, so your installer must correctly size heat-leak protection such as a cooling coil where specified by the manufacturer, along with the other required safety components for a solid-fuel wet system. In Ireland, Technical Guidance Document J (Heat Producing Appliances) sets the baseline for safe flues, hearths, and combustion air, while Part L drives the efficiency detail you will want signed off. Getting these fundamentals aligned with the appliance manual makes day-to-day use far more predictable, which is what most homeowners really want when they are relying on the stove for heat and hot water.
Frequently Asked Questions About Boiler Stove Central Heating Installation and Safety
Do I need a chimney liner for a boiler stove in Ireland?
Often, yes, but it depends on the condition and size of the existing flue and the stove manufacturer’s requirements. Many older Irish chimneys are oversized, rough internally, or leaky, which can weaken draught and increase the risk of smoke spillage. Your installer should assess the chimney, confirm suitability for solid fuel, and follow the stove manual and Technical Guidance Document J for safe flue design, clearances, and commissioning.
Can a boiler stove run my radiators and hot water?
A boiler stove can be connected to radiators and, in many cases, domestic hot water, but it has to be designed and installed as a full wet system with the correct safety controls. The system design depends on the stove’s boiler output (to water), the heat demand of the property, and how the stove integrates with any existing boiler or hot water cylinder. Because overheating risk is a key hazard with solid-fuel boilers, the safety equipment specified by the stove manufacturer is not optional.
Do I need an external air kit in an Irish home?
You may, particularly in newer builds, deep retrofits, or homes with upgraded windows and doors where natural infiltration is reduced. A stove that cannot get enough combustion air can burn poorly, smoke more, and become harder to control, and it can also increase the risk of flue spillage under certain conditions. Your installer should assess ventilation requirements as part of the overall installation design and in line with Irish guidance for heat producing appliances.
What safety devices are typically required on a boiler stove wet system?
The exact list depends on the stove and the system design, but the critical point is that boiler stoves need dedicated protection against overheating. Many installations require a heat leak route and may require a cooling coil, depending on the appliance specification, as well as correctly set up controls and plumbing arrangements that safely move heat away from the stove. Always follow the manufacturer’s instructions and use an experienced, competent installer, because these components are there to prevent dangerous boil-over scenarios.
What Irish building regulations apply to stove installation?
The core reference for solid-fuel stoves, flues, hearths, and combustion air is Technical Guidance Document J. Energy efficiency requirements are generally supported by Part L, which influences how the overall home energy performance and efficiency measures are approached. Your installer should be able to explain what applies to your home, document what was fitted, and confirm commissioning checks were completed.
Where should I place carbon monoxide alarms?
Follow the alarm manufacturer’s instructions and place alarms in appropriate locations for solid-fuel appliances, including the room with the stove. Carbon monoxide is colourless and odourless, so an alarm is a vital safety backstop rather than an optional extra. It is also sensible to ensure alarms are tested during commissioning and checked regularly as part of normal home safety.
Compare Boiler Stoves That Suit Irish Wet Heating Setups
If you are planning to connect a stove to radiators or hot water, shortlist a few models with the right boiler output and flue options before you talk through the installation details with your installer. Browse the range of boiler stoves in Ireland to compare sizes, outputs, and EcoDesign-ready options, so you can move into the install conversation with clearer, safer choices.
Integrating with Existing Heating Systems
A boiler stove can integrate with an oil or gas boiler because you are simply adding a second heat source to the same radiator and domestic hot water circuit. That can reduce boiler run time when the stove is lit and the system is set up correctly. It only works safely when the pipework and safety devices let excess heat escape during a power cut, pump failure, or control fault. The main complication is whether your system is open-vented or sealed, because the wrong arrangement can boil water and over-pressurise very quickly, so the plumbing design matters as much as the stove.
Open-vented vs sealed: what changes?
This matters because solid fuel keeps producing heat after you “turn it off”, so the system must always have a safe path to shed heat. In Ireland, SEAI’s Domestic Technical Standards and Specifications notes that solid fuel systems should use normally open motorised valves so circulation is not accidentally blocked if there is a control failure or loss of power. See the SEAI document here: Domestic Technical Standards and Specifications (SEAI). Getting the venting, expansion, and heat leak arrangement right is what makes the controls and valve logic safe rather than just convenient.
Controls, valves, and who does what
This matters because controls decide which heat source is active, and valves decide where the heat is allowed to go. You typically want proper interlocking so the boiler and stove do not end up fighting each other, along with a fail-safe heat-dump or heat-leak route that still works when something goes wrong. A qualified, experienced installer should design and commission this, using the stove manufacturer’s instructions and Irish good practice, because small details like valve type, pipe sizing, and pump placement are what prevent nuisance overheating. When you are browsing boiler stoves in Ireland, it helps to keep one eye on your existing heating layout and another on heat output, because the split between room heat and boiler output is what determines whether the stove will suit your radiators and hot water demand.
Efficiency and Heat Output
The response you get from a boiler stove depends on how it splits heat between the room and the water circuit. Most Irish buyers start with the manufacturer’s data plate (nominal output and boiler output), because that tells you whether you’ll get cosy radiant heat in the room or most of the heat pushed out to radiators and hot water. In real homes, the “right” figure still shifts with fuel quality, chimney draught, and how hard you run the stove, so treat brochure numbers as a baseline rather than a guarantee.
Nominal vs boiler output (what you’ll actually feel)
Nominal output is the total heat the stove produces, while boiler output is the share sent to water. When you’re comparing models in the boiler stove collection, check both figures so you don't end up with an overheated room and lukewarm rads (or the other way around), especially in typical Irish homes where you may be heating a sitting room while supporting a radiator circuit.
Efficiency, emissions compliance, and air-wash glass
In Ireland, it makes sense to prioritise Ecodesign-compliant appliances, as SEAI explains that EU ecodesign requirements apply to product groups including solid fuel local space heaters placed on the market here, with a strong focus on efficiency and emissions limits. Air-wash helps day to day by directing pre-heated air down the inside of the glass, which reduces soot and keeps the view clearer when you burn properly seasoned wood, and that cleaner burn tends to show up in both performance and maintenance effort.
Maintenance and Fuel Consumption
If you skip servicing and sweeping, your boiler stove can start drinking fuel, soot up the boiler waterways, and even smoke back into the room. That lines up with standard installer practice and manufacturer guidance: once the draught drops, the fire burns dirtier and you get less usable heat into your radiators. The knock-on is slow and expensive because the problem builds over a heating season rather than in a single bad night, and it tends to show up as “it’s not heating like it used to”.
Expected fuel use at nominal output
At a steady “nominal” burn, you can estimate wood use from energy content. SEAI lists hardwood at 20% moisture at 4.16 kWh/kg in its Domestic Fuel Cost Comparison, so a 10 kW output is roughly 2.4 kg per hour before efficiency losses and hot-water demand are factored in. In real Irish use, that number shifts with wood moisture, draught, stove settings, and how much of the boiler output is actually being taken away by your heating circuit, which is why upkeep and correct operation matter as much as the headline kW.
Annual servicing and chimney-sweeping
A sensible Irish routine is one professional service yearly, ideally before winter, and at least one chimney sweep. Many stove manuals state the chimney and connecting flue must be swept at least once a year to keep draught stable and reduce soot-related problems, such as this example from a Henley manual: “the chimney and connecting flue must be swept at least once a year”. When you’re comparing options, it helps to shortlist by output and layout from a boiler stove collection and factor in the practical reality that a boiler model tied into radiators and hot water rewards steady, well-maintained running far more than stop-start burning.
Environmental and Cost Implications
A boiler stove central heating system can cut what you spend on oil or gas straight away if you have access to well-seasoned wood, but it also adds fuel-handling and ash-cleaning work. The proof is in SEAI’s regular fuel-price comparisons, which show Irish heating costs swing sharply depending on fuel and tariff. Over time, the “cheapest” setup is usually the one you will run consistently and keep burning cleanly, not the one that looks best on paper, and that day-to-day reality tends to shape the kind of boiler stove you buy.
Running costs in an Irish home
Running cost comes down to €/kWh delivered to your radiators, and SEAI tracks this in its household fuel price comparison data, published as a downloadable dataset: Household fuel cost comparison (CSV). If you’re weighing options, it helps to compare boiler stoves alongside other wet systems and be honest about your fuel supply, storage space, and how often you will actually light the stove. Once you are clear on that, you can shortlist models by heat output and boiler output split on boiler stoves in Ireland, because sizing is what decides whether the savings feel real in daily use.
Emissions and SEAI grant fit
Emissions matter because a boiler stove shifts pollution from a power station to your own chimney, so fuel quality and burn control become the make-or-break detail in Irish winter air. Clean, dry fuel and a stove that is run correctly generally mean less smoke, less soot in the flue, and a more comfortable heat for the same amount of fuel, which is good for both your neighbours and your maintenance routine.
On grants, the key practical point is that choosing a boiler stove does not align with SEAI heat pump supports, because the Better Energy Homes scheme is geared around measures like Heat Pump Systems rather than solid-fuel boiler installations, and the heat pump grant can be worth up to €12,500 depending on dwelling type. That difference can be a big swing in overall budget, so it is worth settling your approach early, especially when the “right” model often comes down to matching boiler output to your existing radiators and hot water demand.
How Boiler Stoves Fit into Broader Home Heating Solutions
Match your boiler stove plan to how your home is laid out and how you actually use heat day to day. SEAI’s BER-based modelling is a good reminder that space heating is the main event in Irish homes, but real comfort often comes from quick, room-by-room top-ups when you need them. In practice, a boiler stove can provide steady “background” heat through radiators and hot water, while other appliances cover convenience and timing in the rooms you use most.
Pairing a boiler stove with “instant” heat in living spaces
Because space heating made up 61% of household energy use in 2020 in SEAI’s estimate of final energy by end-use, it can make sense to use a boiler stove for the heavy lifting and an electric fire for fast, controllable warmth in the room you are actually sitting in. That split also helps when you want a bit of heat at shoulder seasons without running the whole system, which is often where day-to-day running costs feel most noticeable.
Where cooker ranges fit
A cooker range can suit Irish homes where the kitchen is the hub, letting you prioritise heat where you spend the most time, while the boiler stove supports radiators and hot water elsewhere. It is a very lifestyle-led choice as much as a heating one, so it works best when the layout, flue route, and how you cook and live line up with the way the heat will naturally spread through the house. That practical “heat where you are” mindset is also what makes it easier to compare other room-heating options without overcomplicating the system.
What are the benefits of a boiler stove over traditional heating systems in Ireland?
A boiler stove can heat the room it sits in while also sending heat to radiators and, in many setups, your hot water cylinder. That can reduce reliance on oil or gas during the shoulder seasons, keep heat available during outages (depending on your system design), and make better use of local solid fuel options.
You also get more direct control over how and when heat is produced, which many Irish households like in older homes with colder living areas. If you burn logs, fuel quality matters: Ireland introduced tighter rules for wood sold in small quantities, including a limit of 25% moisture content, moving to 20% within 4 years, to cut smoke and improve combustion efficiency, as set out in a Government of Ireland announcement dated 7 September 2021 Government of Ireland press release on solid fuel standards.
How does a boiler stove work in a central heating system?
Inside a boiler stove, the fire heats a water jacket (the boiler) as well as radiating heat into the room. A circulating pump and heating controls move that hot water through your pipework to radiators and, where fitted, a coil in the hot water cylinder.
Most Irish installations include safety and heat management components such as a correctly sized feed and expansion (in open vented systems), heat leak radiator, pump and thermostat control, and suitable pipework for high temperatures. The exact layout depends on whether the system is open vented or sealed, what fuel you are using (wood, multi fuel, or pellet), and whether you are combining the stove with another heat source.
Are boiler stoves suitable for new builds in Ireland?
They can be, but suitability in a new build usually comes down to compliance, ventilation, and system design rather than the stove itself. New homes tend to be more airtight and better insulated, so the stove output and the heat split between room and boiler need to be chosen carefully to avoid overheating and to keep the stove operating cleanly.
From a regulatory point of view, solid fuel appliances and flues should be designed and installed to meet Irish Building Regulations guidance in Technical Guidance Document J Department of Housing Technical Guidance Document J, while overall energy performance targets for dwellings are supported by Technical Guidance Document L Department of Housing Technical Guidance Document L for dwellings. A competent installer and a designer familiar with modern Irish airtightness and ventilation strategies are key.
What safety features should be prioritized when choosing a boiler stove?
Prioritise safety features that protect against overheating, fumes, and installation risks:
Overheat protection: a thermal safety valve and, where appropriate, a cooling coil for systems that could be at risk of boiling.
A dedicated heat dump route: often a heat leak radiator that can dissipate heat if controls fail or power is lost.
Correct flue compatibility: the appliance and flue system must be matched, correctly sized, and properly terminated.
Safe clearances and hearth requirements: non-combustible materials and manufacturer clearances matter as much as kW output.
Reliable controls and sensors: boiler stat, pump control, and suitable high limit protection reduce the chance of uncontrolled temperatures.
Even the best stove can be made unsafe by a poor installation, so align the appliance choice with Irish guidance on heat producing appliances and flues in TGD J Technical Guidance Document J.
How do boiler stoves integrate with existing oil or gas heating systems?
Integration is common in Ireland, but it must be engineered so the heat sources do not fight each other and so the boiler stove cannot overheat the system. Many homes use an oil or gas boiler for automatic background heat and hot water, with the boiler stove adding heat when you light it.
Typical integration approaches include:
Link-up plumbing with proper separation: using a heat exchanger or a correctly designed link-up kit so the solid fuel circuit can stay safe, particularly if the existing system is sealed.
Interlocking controls: wiring so the oil or gas boiler backs off when the stove is producing usable heat, while still protecting hot water temperature.
Correct safety route for excess heat: ensuring the stove side can always dissipate heat, even if valves close or power is interrupted.
Because system types vary widely across Irish housing stock, the safest path is to confirm your existing setup and have the integration designed around it. Keeping up with practical, Ireland specific guidance makes those decisions feel far less daunting, especially when you have one place to get updates as standards and best practice evolve.
Stay warm and informed! Subscribe to our newsletter for the latest tips on choosing and using home heating products in Ireland.
If you are weighing up outputs, fuel types, and system compatibility, browse our range of boiler stoves in Ireland and keep the guidance coming to your inbox.