How to Safely Use a Boiler Stove During Power Cuts in Ireland
Using a boiler stove during a power cut matters because a system designed around an electric pump can overheat fast when circulation stops.
In Ireland, you are often relying on the stove to keep the house liveable when the grid is down, but the same conditions can create real risks, including boiling water in the boiler, rapid pressure rise, venting through safety valves, and scalding from hot pipework. You stay safer by knowing how your stove is plumbed, what should happen when the pump is off, and whether you have a dependable heat escape route such as a gravity circuit or heat-leak radiator that continues to move heat without electricity.
You also need to understand how a boiler stove ties into your existing radiators and hot water cylinder, which safety devices must be present and working, and what trade-offs come with backup options like a battery, inverter, or UPS for pumps and controls. Irish compliance and commissioning details matter too, especially where Building Regulations, energy assessments, and documentation affect insurance, resale, and future upgrades.
Take a moment to check what protection your system has when power is lost, so you can keep heat where you need it and avoid dangerous temperature and pressure build-up.
Understanding Boiler Stove Safety During Power Cuts
Treat a power cut as a safety event if you have a boiler stove, because it is heating water as well as the room. When electricity drops, the stove can keep producing heat long after the circulating pump stops, and that heat still needs somewhere safe to go. Some systems are designed to shed heat safely even during an outage, while others rely on the right plumbing layout and safety devices to prevent overheating, so the details of your installation really matter.
Why power cuts change the risk profile
A power cut matters because the circulating pump may stop, and hot water cannot move heat away from the boiler stove quickly enough. In Ireland, the safety expectations around solid-fuel appliances, chimneys, flues, hearths and ventilation are set out under Part J of the Building Regulations, with practical guidance in Technical Guidance Document J (Heat Producing Appliances), which is exactly the kind of risk scenario those requirements are designed to reduce. When heat is trapped in the boiler and pipework, temperature and pressure can rise quickly, which is why installers plan for “pump-off” conditions rather than assuming the electrics will always be there.
What you should have in mind before the lights go out
A power cut is not the time to chance it, so you are better off knowing your setup and what your installer designed as the safe heat path. At a minimum, be clear on the basics: whether the stove is linked to radiators and a hot water cylinder, what safety devices are fitted, and whether the system has a reliable way to dissipate excess heat without power, all in line with the manufacturer instructions and good Irish installation practice. If you are still comparing options, browsing boiler stoves in Ireland helps you shortlist models, then you can ask the right questions about safe heat dissipation and controls during outages, which tends to shape the rest of the system design as much as the stove choice itself.
Frequently Asked Questions About Boiler Stove Safety During Power Cuts
Are boiler stoves safe to use during a power cut?
They can be safe, but only if the system is designed and installed to cope with a pump stopping while the fire is still producing heat. The key issue is heat removal from the boiler side; if water cannot circulate, the stove can overheat. Your installer should follow the stove manufacturer’s instructions and Irish Building Regulations guidance (including TGD J) so the installation includes appropriate heat dissipation and safety protection for abnormal conditions such as power loss.
Why is a boiler stove riskier than a room-heater stove in an outage?
A room-heater stove mainly sheds heat into the room by convection and radiation. A boiler stove sends a large portion of its output into water, so if circulation stops, that heat can build up in the boiler and pipework. That is why boiler stove systems often need additional safety planning compared with a dry stove, especially in typical Irish setups where the stove is tied into radiators and a cylinder.
What should be built into an Irish boiler stove system to handle a pump failure?
The exact solution depends on the appliance and how the system is plumbed, but you should expect your installer to provide a safe route for excess heat and suitable safety components, fitted to the manufacturer’s specification. In many Irish installations, that means planning for gravity circulation where appropriate, ensuring correct pipe sizing and layout, and using the correct safety controls and valves specified for solid-fuel wet systems. The important point is that it is not an optional extra; it is part of making the appliance safe and compliant in real-world conditions.
Does TGD J cover boiler stove power-cut safety directly?
TGD J is guidance on meeting Part J of the Building Regulations for heat producing appliances, including safe installation, flueing, protection of the building, and combustion air and ventilation considerations. It supports the broader safety expectation that appliances are installed in a way that avoids dangerous situations, which is highly relevant when considering scenarios like loss of power and loss of circulation in wet solid-fuel systems. Your installer should also follow the specific boiler stove manual, as the manufacturer requirements are central to safe system design.
If I already have a boiler stove, what should I check before winter?
Confirm exactly how your system is intended to behave during a power cut. Ask your installer or service technician to identify the safety devices fitted, the intended heat dump or dissipation path, and any operational limitations you should follow during an outage. It is also worth checking you have suitable CO alarms, a properly maintained chimney and flue, and that your ventilation provisions have not been blocked or altered during renovations, because safe combustion is part of safe operation in every season.
Compare Boiler Stoves Built for Real Irish Homes
If you are choosing a boiler stove or upgrading an older setup, shortlist a few models and have a proper conversation with your installer about safe heat dissipation during a power cut, the controls you will rely on, and the flue and ventilation requirements for your house. Browse the boiler stoves in Ireland collection to compare outputs and formats, then use that shortlist to confirm a safe, compliant design before you buy.
Safe Operation During Power Cuts
Use a boiler stove cautiously during a power cut because the pump may stop and the stove can still be producing heat into the boiler. Treat it like a circulation failure: keep the fire small, shed heat quickly, and keep an eye on boiler temperature. If you are not 100% sure you have a correctly installed gravity circuit and a heat-leak radiator that can move heat with no electricity, stop firing and contact your installer before the system overheats.
1. Reduce the fire and avoid over-fuelling
A boiler stove can keep making heat after the pump stops, so do not add fresh fuel. Close the air controls down to a safe, steady burn and avoid opening the door more than you need to, as a sudden rush of air can drive the fire harder when you are trying to keep temperatures under control.
2. Make sure heat can escape without electricity
You want a gravity-fed heat-leak path, often a dedicated radiator, so heat can rise away naturally even with no pump running. Confirm this is part of your system design and that it is kept unobstructed and usable, as it is a key safety feature for boiler stoves in Irish homes. If you are comparing appliance options, it also helps to understand how typical setups are configured on boiler stoves in Ireland, as plumbing design and safety controls are just as important as heat output.
3. Keep carbon monoxide safety in mind while you manage the outage
During low-draught conditions, carbon monoxide risk can rise, particularly if the stove is slumbering or the chimney is cold. Make sure you have suitable CO alarms fitted and working, in line with the Carbon Monoxide Alarm Regulations 2022, and keep ventilation pathways clear so the appliance can burn cleanly while you keep the fire under tight control.
Integrating Boiler Stoves with Existing Heating Systems
Integrating a boiler stove with your existing radiators and hot water needs careful design in Ireland because a solid-fuel appliance keeps producing heat long after you light it, and that heat still has to go somewhere safely. You cannot simply “tie in” like another on-demand heat source, as SEAI guidance highlights the need for dedicated safety measures on solid-fuel systems to prevent overheating if circulation stops. The right layout depends on whether you are linking into an open-vented hot water cylinder, an existing oil or gas boiler setup, and what happens to pumps and controls during a power cut, which is why a competent, experienced installer matters so much.
How the stove feeds radiators and hot water
A typical Irish setup routes stove heat to the cylinder coil and the radiator circuit through the correct plumbing arrangement, controls, and usually a heat exchanger or separation strategy where required to protect existing components. A good starting point is to check the stove’s room-to-water output split so you are not overheating the room while still under-serving the radiators and hot-water demand, and you can compare options on boiler stoves in Ireland with that balance in mind. Once the heat output is matched, the real question becomes how the system behaves when everything is not running perfectly.
Why safety devices matter most during outages
Overheat protection is the make-or-break detail because, during a power cut, the circulating pump can stop while the fire is still roaring and the water in the boiler circuit can rapidly climb in temperature. Installers typically use correctly specified safety components such as pressure relief valves and a thermal dump (heat-leak) circuit to safely shed excess heat, in line with the approach outlined in the SEAI Domestic Technical Standards and Specifications for solid multi-fuel heating systems. When these protections are designed properly, you get the comfort and flexibility of solid fuel without turning a routine winter evening into a stress test for your heating system, which also sets the tone for the maintenance and checks you will want to stay on top of.
Irish Regulations and Compliance
Irish Building Regulations for boiler stoves and back boilers are about installing, ventilating, and flueing the appliance so it operates safely in an Irish home. In practice, that means controlling fire risk, preventing smoke and fumes entering the room, and making sure the system can shed heat safely if the electricity goes. The key point is that a boiler stove is both a solid-fuel appliance and a wet-heating heat source, so it needs to satisfy combustion safety and water-side safety together.
What Irish Building Regulations expect
Irish requirements for solid-fuel appliances are set out in the Department’s Technical Guidance Document J (Heat Producing Appliances), which is why flue sizing, safe distances to combustibles, a suitable hearth, and permanent ventilation are not optional details. Manufacturer instructions still matter because TGD J is guidance on meeting the Building Regulations, and the appliance manual sets the tested clearances, flue diameter, and commissioning requirements for that specific model. If you’re still comparing options, it can help to browse boiler stoves in Ireland to get a feel for typical outputs and layouts, and then confirm your installer is happy to certify the full flue-and-vent design as part of the job, because that’s where most real-world issues show up.
SEAI and DEAP notes that matter in outages
SEAI’s BER methodology uses DEAP, and the SEAI DEAP Manual is why it pays to keep proper documentation on the boiler stove’s tested performance, the fuel type, and the exact system configuration. If the stove is being factored into a BER assessment, your assessor generally needs clear product data and an accurate description of how heat is distributed and controlled. For power cuts, the practical compliance headache is heat dump and overheating risk: if pumps stop and heat continues to be generated, the design still needs a safe way to dissipate excess heat using appropriate safety controls specified by the stove and system designer. That is why you should ask your installer to sign off the safety devices and the overall hydraulic design before you ever rely on the stove during a blackout, because the paperwork is only useful when it matches what is actually installed and commissioned in your home.
Do I need to comply with Building Regulations if I am only replacing an old stove or open fire?
Yes. Any change to a heat-producing appliance, the flue, the liner, ventilation provisions, or the hearth can affect safety and must align with the functional requirements of the Irish Building Regulations, with Technical Guidance Document J being the main reference used in practice. Even a like-for-like swap can trigger the need for a flue liner upgrade, changes to permanent ventilation, or different clearance distances because modern appliances often have specific installation conditions in their manuals.
Is a boiler stove treated differently to a standard room-heating stove under Irish guidance?
In practical terms, yes. The combustion side still needs to meet flue, clearance, hearth, and ventilation expectations under TGD J, but a boiler stove also connects into a wet heating circuit, so the system design has to address heat dissipation, safe operating temperatures, and suitable safety controls. That extra water-side complexity is why boiler stoves are not a DIY fit, even where a basic stove replacement might look straightforward on paper.
Will fitting a boiler stove improve my BER automatically?
Not automatically. BER outcomes depend on the full dwelling assessment and how the heating system is recorded in DEAP, including documented appliance performance, controls, distribution losses, and the overall heating set-up, as set out in the SEAI DEAP Manual. If documentation is missing or the installation details are unclear, the assessor may not be able to credit the system as you expect, so keeping manuals, test certificates, and a clear description of the installed layout is worth the small effort.
What is “heat dump” and why is it important for compliance and safety?
Heat dump is a safe method of shedding excess heat from a boiler stove when the system cannot circulate normally, most commonly during a power cut when pumps stop. Because a solid-fuel fire cannot be switched off instantly, the system needs a safe route to prevent overheating, typically through properly designed safety components and an agreed hydraulic layout specified by the installer and the appliance manufacturer’s instructions. It is a critical part of water-side safety, and it is one of the main reasons you should only proceed with a competent installer who will commission and document the safety devices.
Can I install a boiler stove without permanent ventilation if the room feels draughty?
Usually not, and you should not “block up” vents to solve comfort problems. Solid-fuel appliances generally require permanent combustion air, and TGD J sets the expectations around providing adequate air supply to prevent poor combustion and fume spillage. If the room feels uncomfortable, the fix is normally better vent positioning, a suitable vent type, or addressing general draught-proofing and balancing, while still keeping the required air supply in place.
Browse Boiler Stoves That Suit Irish Install Requirements
If you are weighing up a boiler stove or back boiler for an Irish home, start by shortlisting models with the right heat output and clear installation documentation, then sanity-check your chimney, flue route, and ventilation with a qualified installer before you buy. Browse the current range of boiler stoves in Ireland to compare options by size, fuel type, and typical system suitability, so you can move forward with a setup that is safe, compliant, and practical to live with.
Designing for Emergency Situations
Design or retrofit a boiler stove system in Ireland so it stays safe and usable during power cuts by thinking through what fails when the electricity drops, and building in protection for each weak point. Pumps, controls, and motorised valves are usually the bits that stop, which can leave heat trapped in the boiler stove. Aim for a safe gravity heat-dump route plus protected power for essential circulation, and size a battery or UPS setup so it can keep the pump running long enough to ride out common outages. A quick test run before winter is time well spent, because it is the only way to know how your system behaves when the mains goes off.
1. Build in a safe heat-dump route
A gravity-fed heat leak radiator and an open-vented safety arrangement help stop boiling if pumps die, so get your installer to confirm the stove manual’s required safety pipework and safety devices. In Ireland, this is the sort of detail you want aligned with the appliance instructions and normal solid-fuel installation practice, because boiler stoves can keep producing heat even when everything else in the house is dark. Once the heat has somewhere safe to go by natural circulation, backing up the electrics becomes a lot more effective.
2. Keep the pump alive with UPS or battery/inverter
A small UPS can run a boiler-stove circulation pump and basic controls, but the runtime depends on the pump wattage and the UPS battery capacity, so check the actual electrical load rather than guessing. When you are comparing options, the boiler stoves collection helps you sense-check typical pump and control requirements by model, and it can also prompt the right conversation with your installer about what must stay powered during an outage. The important part is keeping the system stable under fault conditions, which is where simple planning beats fancy add-ons.
3. Plan for rural realities
In the country, treat patchy mobile coverage and longer restoration times as normal: store dry fuel, keep a torch by the stove, and practise a power-off lighting and shutdown routine so everyone in the house knows what “safe operation” looks like without relying on apps, timers, or smart controls. It is also worth keeping a short checklist near the appliance with your installer’s advice on what to do if the pump stops or the stove overheats. That bit of preparation is what turns a stressful cut into a manageable evening at home.
Maintenance and Safety Checks
Maintain a boiler stove safely in Ireland by doing a thorough pre-season clean, checking airflow and seals, and confirming the flue is sound so the stove draws properly and burns cleanly. Make sure your safety kit and paperwork are in order, including commissioning details from the original installation. If anything looks off such as smoke spillage, heavy tar deposits, persistent strange smells, or difficulty controlling the burn, stop using it and have it inspected before you depend on it in cold weather, because small faults can become serious quickly once the stove is running daily.
1. Deep-clean the firebox and service parts
A pre-season clean matters because ash and soot restrict airflow, which increases smoke and reduces usable heat into the room and water. Empty and clean the firebox, clear any grate and ash-pan areas, and check baffle plates and internal liners for cracking, warping, or gaps. Clean the glass and the air inlets so you can control the burn properly, and replace worn rope seals on the door if they are no longer making an even, airtight seal. Those basics make the stove more controllable and also reduce the chance of soot and tar building up where you cannot see it.
2. Inspect the chimney/flue and verify CO protection
A safe, well-drawing flue is essential on a boiler stove because you are often running it harder and longer to heat water as well as the room. For Irish installations, the Department of Housing’s guidance in Technical Guidance Document J – Heat Producing Appliances sets expectations around safe flues and carbon monoxide alarms for solid-fuel appliances in dwellings. Use a competent person to check the chimney or liner condition, look for signs of leaks or staining at joints, and confirm the terminal is suitable and clear, as poor draft, blockages, or tar glaze are all common causes of smoke spillage and CO risk. With alarms, fit a suitable CO alarm in the right location and test it routinely, since a clean-looking stove can still produce CO if ventilation or flue performance is compromised, especially in more airtight homes.
3. Keep commissioning evidence and schedule in-season checks
Keep the installer’s commissioning record, any flue or liner documentation, and note service dates so you have a clear history for insurance, future servicing, and troubleshooting. It is also worth keeping the appliance manual to hand for the manufacturer’s maintenance intervals, suitable fuels, and operating ranges, as boiler stoves are sensitive to over-firing and incorrect fuel. When you are comparing replacements or planning an upgrade, the boiler stoves collection is easier to shortlist if you already know your current output, boiler-to-room heat split, and flue size, because those details usually decide what is compatible without major changes.
Choose a boiler stove consultancy approach that gets the basics right before you spend a cent, because tying a solid-fuel appliance into your hot water and radiators adds plumbing, controls, and safety considerations that a room-heating stove does not. Check that the plan suits your Irish home layout, your existing heating system, and the condition of your chimney and flue route. Confirm compliance early using Ireland’s Building Regulations guidance, and make sure ventilation and carbon monoxide risk are treated as design issues, not add-ons. Balance heat-to-room versus heat-to-water so you do not end up with an overheated living room or an underperforming heating circuit, and keep real-world usability in mind for scenarios like power cuts. With a clear brief, you can shortlist suitable boiler stoves that are actually available in Ireland and hand your installer a sensible, safer specification to work from.
How Consultants Help with Boiler Stove Installations
Experts generally agree that boiler stoves are simple to love but tricky to plan, because you’re tying solid-fuel heat into water, radiators, and safety controls. In my experience on Irish installs, the difference between “grand” and ongoing headaches is usually decided before the stove is ever lit. Your house layout, existing plumbing, and chimney condition all change what’s sensible, and it is that reality check that makes professional input valuable.
Planning the system before you buy
Good consultancy starts with compliance-first design, using Ireland’s building guidance like the Department of Housing’s Technical Guidance Document J for heat producing appliances (current edition published 4 December 2020) to sanity-check flues, ventilation, and CO risk in the same pass. When the basics are confirmed early, your choices narrow to models and system layouts that can actually be installed safely and signed off without awkward compromises.
Safer shortlisting for your home (and your installer)
Practical advice helps you shortlist the right heat-to-water balance, then match it to what’s actually available in Ireland, such as this boiler stoves collection, so the next step can focus on safe operation during power cuts. That last point matters because a boiler stove is part of a wider system, and the way it behaves when pumps or controls are off can be just as important as the headline kilowatts.
Frequently Asked Questions About Boiler Stove Consultants in Ireland
Do I need a consultant to install a boiler stove in Ireland?
You are not generally required to hire a “consultant” as a formal role, but you do need competent design and installation input because a boiler stove interacts with your plumbing, hot water cylinder, radiators, safety devices, and the flue system. Many homeowners get the same outcome by using a suitably qualified installer and agreeing the system design before purchase, with compliance checked against Irish Building Regulations guidance such as Technical Guidance Document J. The key is having one person clearly responsible for the overall plan, not just fitting the appliance.
What will a boiler stove consultant or installer look at before you buy?
Expect them to assess your chimney and flue route, ventilation provision, hearth and clearances, and where the appliance will sit in the room. On the heating side, they will look at your existing pipework, cylinder type, radiator circuit, controls, and where safety components can be installed. They will also consider how the stove’s heat output is split between the room and water, because that balance is often what decides comfort and day-to-day usability in an Irish home.
How do I choose the right heat-to-water balance for my house?
It depends on your room size, insulation levels, how open-plan the space is, and how much of the stove’s job is supporting radiators or domestic hot water. Too much room heat can make the living space uncomfortably hot, while too little water heat can leave you disappointed with radiator performance. A practical way to narrow it is to start from the rooms and hot water demand you actually want to support, then choose a boiler stove output split that aligns with that, rather than buying based on total kW alone.
Are boiler stoves suitable during Irish power cuts?
This is a planning issue, not just a product question. Many boiler stove setups rely on pumps and controls to move heat safely around the system, so you need to think through what happens if electricity is lost while the stove is running. Your installer should design in the appropriate safety approach for your specific system and follow the stove manufacturer’s instructions and Irish guidance, because the risks depend on the plumbing layout, the controls, and the safety devices used.
What Irish regulations or guidance apply to boiler stove installations?
Installations should align with the Irish Building Regulations and associated guidance, including the Department of Housing’s Technical Guidance Document J for heat-producing appliances, which covers key considerations such as flues, ventilation, and safety. You also need to follow the appliance manufacturer’s installation manual, and the work should be carried out and certified as required by the relevant competent professionals. Getting these checks done at the planning stage usually prevents expensive changes later.
Can I connect a boiler stove to an existing oil or gas heating system?
Sometimes, yes, but it is not a universal “drop-in” job. Linking a solid-fuel boiler stove with an existing system can involve compatibility checks around controls, pipework, cylinders, and safety arrangements, and it must be designed properly to avoid unsafe operating conditions. This is exactly where experienced system planning pays off, because the best solution depends on what you already have, how you heat the house day to day, and how you want the systems to work together.
Shortlist a Boiler Stove That Fits Your Home and Your Install
If you are at the choosing stage, start by narrowing to boiler stoves that are actually available for delivery in Ireland and suit the kind of heat-to-water split your installer can safely integrate. Browse the boiler stoves collection to compare options, then bring your room details, chimney setup, and current heating layout to your installer so you can lock in a compliant plan before you buy.
Can I safely light or run a back‑boiler stove during a power cut in Ireland?
Sometimes, but only if your system is designed to shed heat without electricity. In a typical Irish boiler stove setup, the circulating pump and motorised valves are powered, so a power cut can stop heat moving away from the stove.
If you have a properly sized gravity circuit and a permanently open heat-leak radiator (or an equivalent heat-dump arrangement), the stove can continue to move heat by natural circulation and reduce the risk of overheating. If you are not certain you have that safety route, treat a power cut as a reason to stop fuelling the stove, close the air controls, and let the fire die down rather than lighting or building it up.
What happens to a boiler stove or back boiler if the circulating pump stops?
When the pump stops, water flow through the boiler can slow dramatically or stop completely. The stove can still be producing a lot of heat, so the water in the back boiler can overheat and start to boil, which can cause:
Kettling and rapid temperature rise in the boiler.
Discharge from safety devices such as the open vent and feed and expansion cistern on open-vented systems, or a temperature and pressure relief path where fitted.
Steam and scalding risk near the pipework, especially at the highest points.
The core hazard is trapped heat. The safest response during an outage is to reduce combustion quickly, avoid adding fuel, and make sure any heat-leak radiator is able to take heat without valves restricting it.
Do boiler stoves need a gravity circuit or heat‑leak radiator for safety?
For most boiler stoves in Irish homes, some form of heat dump that works without mains power is a key safety feature. A gravity circuit to a heat-leak radiator gives hot water a path to circulate naturally when the pump is off, helping prevent boil-over.
Whether it is mandatory in your case depends on the appliance instructions and how the system is designed and commissioned, but you should assume it is essential unless a competent installer has confirmed an alternative, compliant method of heat dissipation that is safe during a power cut.
How does a boiler stove connect into an existing central‑heating system in Ireland?
A boiler stove is usually tied into a wet heating system using a dedicated pipe circuit from the stove to the hot water cylinder and heating distribution, with controls and safety components designed around solid-fuel “uncontrolled” heat.
Common Irish integration approaches include:
Open-vented primary circuit from the stove with a feed and expansion cistern and open vent, so expanding water has a safe route.
Gravity circulation section to the cylinder coil and a heat-leak radiator, so the stove can dump heat even if pumps are off.
Pumped, zoned central heating for the rest of the radiators, typically with motorised valves, interlocks and thermostats.
Linking to an existing oil or gas boiler using a neutraliser, thermal store, or heat exchanger arrangement, so one heat source does not unintentionally overheat the other.
Because these systems are safety-critical, the correct layout is driven by the stove manufacturer’s instructions and Irish compliance requirements, not just what fits the existing pipework.
Are there battery backup or UPS options for boiler stoves during power cuts?
Yes, but they are not a substitute for passive safety. A UPS or battery-inverter setup can keep a circulation pump and key controls running during a short outage, which can stabilise temperatures and give you time to safely wind the stove down.
When considering backup power, look for:
Pure sine wave output for compatibility with many pump motors and boiler controls.
Enough surge capacity for motor start-up, not just steady running.
A clear wiring and switching plan that avoids back-feeding and keeps essential circuits separate.
Treat backup power as an added layer, not the only layer. Solid-fuel appliances can keep generating heat after you cut electrical power, which is why Irish energy assessment guidance explicitly categorises solid fuel boilers, including open fires with back boilers, as their own type of heating system in SEAI documentation such as the DEAP Manual. If you want a practical, homeowner-friendly way to stay safe through outages, it helps to keep a short checklist and trusted guidance close to hand.
Stay warm and prepared by subscribing to our newsletter for essential tips on heating safety and efficiency in Ireland.
If you are considering upgrading, repairing, or reconfiguring your setup for safer operation during outages, browse our range of boiler stoves to see options suited to Irish homes.